Synthesis and optical properties of new chalcones containing 4-[bis(2-hydroxyethyl)amino]phenyl fragment

New chalcones with 4-[bis(2-hydroxyethyl)amino] phenyl fragment were obtained from 4-[bis(2-acetoxyethyl) amino]- benzaldehyde by the Claisen–Schmidt reaction. From their UV-VIS absorption and emission spectra, optical band gap values were calculated based on the Stokes shifts as well as the molar absorption coefficients and fluorescence quantum yields were estimated. The dependence of the absorption and emission maxima on solvent polarity and pH was evaluated.     

输电铁塔四地脚螺栓塔脚板抗拉承载力试验与计算方法研究

针对架空输电线路铁塔中常用的四地脚螺栓塔脚板进行了抗拉承载力试验和理论计算方法研究。首先,选取8个试件进行塔脚板抗拉承载力试验研究,分析塔脚底板板厚及有无加劲板对塔脚板抗拉承载力的影响;其次,通过有限元模拟塔脚板的应力分布情况,并结合“塑性分析,弹性设计”的思想,提出了一种基于屈服线理论的四地脚螺栓塔脚板抗拉承载力计算公式;最后,与试验结果、有限元仿真结果、已有技术规定中的计算结果进行了对比。结果表明:建议公式与试验结果和仿真结果较为吻合,相关技术规定中的计算结果偏于保守,验证了本文建议公式的精确性;底板厚度和加劲板的作用对塔脚板承载力影响较大。研究结果可为输电铁塔四地脚螺栓塔脚板结构设计提供参考。     

基于相场描述的拉压不对称强度结构拓扑优化

运用了基于相场描述的拓扑优化方法，来寻找在拉伸和压缩中表现出不对称强度行为的连续体结构的最优布局。依据Drucker-Prager屈服准则和幂率插值方案，优化问题可以描述为在局部应力约束下的最小化结构的体积。用qp放松法来解决应力约束的奇异性，并采用基于P-norm函数的聚合方法对应力约束进行凝聚，该方法实现了约束个数的降低，同时引入了稳定转化法来处理大量的局部应力约束和高度非线性的应力行为，以修正应力，提高优化收敛的稳定性。在优化问题求解时，使用拉格朗日乘子法对目标函数和应力约束进行处理。利用伴随变量法进行灵敏度分析，并通过求解Allen-Cahn方程更新相场函数设计变量。数值算例证明了该优化模型和相应数值技术的有效性，相关算例还揭示了考虑拉压不同强度和考虑同拉压强度约束时得到的结构优化拓扑构型具有显著的差异。     

介质材料二次电子发射特性对微波击穿的影响

以介质填充的平行板放电结构为例,本文主要研究了介质填充后微波低气压放电和微放电的物理过程.为了探究介质材料特性对微波低气压放电和微放电阈值的影响,本文采用自主研发的二次电子发射特性测量装置,测量了7种常见介质材料的二次电子发射系数和二次电子能谱.依据二次电子发射过程中介质表面正带电的稳定条件,计算了介质材料稳态表面电位与二次电子发射系数以及能谱参数的关系.在放电结构中引入与表面电位相应的等效直流电场后,依据电子扩散模型和微放电中电子谐振条件,分别探讨了介质表面稳态表面电位的大小对微波低气压放电和微放电阈值的影响.结果表明,介质材料的二次电子发射系数以及能谱参数越大,介质材料的稳态表面电位也越大,对应的微波低气压放电和微放电阈值也越大.所得结论对于填充介质的选择有一定的理论指导价值.     

A technique for in situ X-ray computed tomography of deformation-induced cavitation in thermoplastics

Deformation-induced cavitation influences the mechanical response of polymeric materials, but acquiring in situ measurements of the spatial evolution of cavities has typically necessitated the use of synchrotron radiation sources. The objective of this study is to develop and demonstrate a method allowing for in situ measurements of deformation-induced cavitation in axisymmetric polymer specimens, using a home-laboratory X-ray computed tomography setup. The method is demonstrated by assessing deformation-induced cavitation of mineral-filled PVC in a repeated loading-unloading experiment. A temporal resolution of about 3 s is obtained by exploiting the axisymmetry of notched round tensile specimens. The evolution of relative density was captured throughout the experiment, revealing an interplay between void nucleation and void growth. Combined with surface deformation measurements obtained by digital image correlation, the present technique yields data suitable for calibration and validation of material models.     

Design and optimization of a cavitating device for Congo red decolorization: Experimental investigation and CFD simulation

The aim of this work is to perform design and optimization of a cavitating device based on CFD simulation. A set of operational and geometrical parameters such as convergence angle, divergence angle, length of throat, and inlet pressure that can affect the hydrodynamic cavitation phenomenon generating in a Venturi are evaluated through CFD simulation and experimental approaches. Response surface methodology (RSM) was employed to achieve the optimum geometrical configuration. The CFD results show that the maximum cavitation zone in the Venturi can be obtained when half angle of the convergence section, throat length and half angle of the divergence section are 22.7°, 4 mm, and 6.5°, respectively. A maximum decolorization of 38.8% has been obtained using the designed Venturi at cavitation number (Cv) of 0.12. Additionally, the results were compared to that of various orifice plates. A decolorization of 26.2% using 33 holes orifice plate and 11.55% in one hole orifice plate approved the superiority of the designed Venturi.     

Controlling thermomechanical behavior of semicrystalline hydrogenated polynorbornene through the cis- to trans-cyclopentylene ratio

Though polynorbornene synthesized by ring-opening metathesis polymerization has an intrinsically all-cis configuration of the cyclopentylene backbone rings, a fraction of these rings can be epimerized to the trans configuration during hydrogenation over suitable catalysts. By varying the method of hydrogenation, semicrystalline hydrogenated polynorbornenes (hPNs) with trans levels between 0 and 36% were obtained. With increasing trans content, the glass transition temperature, melting point, and enthalpy of melting decrease modestly. By contrast, the temperature at which the hPN crystal transitions into a rotationally disordered polymorph varies strongly with trans content, ranging from 126 °C (all-cis) to 71 °C at 27% trans; at trans contents of 34% and above, no rotationally-ordered phase is observed at any temperature. The room-temperature Young's modulus shows no dependence on trans content, while the yield stress drops by 20% at 1% trans content and slowly decreases further with additional epimerization. The temperature dependence of the Young's modulus differs for trans-containing versus all-cis polymers, while the temperature dependence of the yield stress is set by the polymorph type (rotationally ordered vs. disordered).     

IM-5分子筛在Ni-Cu催化剂甲烷热裂解制氢反应中的作用研究

甲烷热裂解制氢并生成高附加值的纳米碳材料,被认为是极具发展前景的氢气生产途径,但高性能催化剂的研发仍存在诸多挑战.我们选择多种载体(TS-1、 IM-5、 Y、介孔SiO₂、 γ-Al₂O₃、 CNTs),采用浸渍法制备Ni-Cu负载催化剂,通过低温N2吸附-脱附、 XRD、 SEM和H₂-TPR等系列表征方法对样品进行分析,考察不同载体对催化剂甲烷裂解制氢和纳米碳材料的影响.实验结果发现,分子筛载体独特的孔道结构有利于金属颗粒的分散,能有效避免反应中界面效应导致的催化剂失活,可提高催化剂反应活性并延长反应寿命,也显著提高了其碳产率.其中以IM-5分子筛为载体的催化剂表现最佳,在反应温度为700℃时, NiCu/IM-5催化剂甲烷转化率高达80%,氢气选择性达100%,反应400 min后活性未见明显降低. NiCu/IM-5催化剂碳产率高达1 446 g_C/g_cat,是NiCu/SiO₂催化剂的5.7倍, NiCu/γ-Al